iXtreme 1.6 xBox 360 firmware flashinimo gidas ir programos: Lite-ON Jungle Flasher
Sveikas atvykęs į topzone.lt!
Jūs esate neprisijungęs. Jei norite naudotis visomis forumo galimybės, Jums reikia užsiregistruoti. Registracija yra labai paprasta, greitai ir svarbiausiai nemokama!
Prisijunk dabar ir naudokis visomis topzone.lt forumo galimybėmis. Prisijungęs galėsi:
Skaityti ir rašyti visuose topzone.lt forumuose.
Gauti ir siųsti asmenines žinutes, su kitais nariais bendrauti el. paštu ar skype.
Užduoti rūpimus klausimus, kuriuos atsakyti padės kiti diskusijų dalyviai.
Šis gidas galioja, tik jei flashinate konsolę, kurioje yra įrašyta bet kokia iXtreme versija.. Jei norite flashinti naują, ką tik pirktą xbox360 su liteon DVDrom, tai jums papildomai reiks nusipirkti Probe įrankį, kuris leis pirmą kartą nuskaityti DVD raktą.
Dar ck3 probe galima ieškoti. ~10pounds jo kaina maždaug.
(Žinoma, pigiau turbūt Lietuvoje paprasčiausiai nunešti meistrui, kad jis nuflashintų naują x360 pirmą kart. Po to jau žinododami DVD ROm raktą, galėsite sekančius kartus flashinti patys namuose, nes nebereiks papildomų įrankių kaip Probe..)
Pirmiausiai jums reiks išardyti savo xBox360. Aš nusipirkau šį įrankių rinkinį http://www.dealextreme.com/details.d...721~r.49994175 kadangi xBox daug kvailų, skirtingų varžtų, jei norėsit atsukti patį DVD ir t.t.
Make sure to have iXtreme 1.6 for Lite-ON (REPACK) in the firmware folder that is within the Jungle Flasher folder so you can utilize the autospoof feature! The Lite-ON ix1.6 repack will need to be renamed to ix16-liteon.bin
Citata:
If your onboard SATA is compatible, you can skip the steps for removing the VIA driver.
In this tutorial I am using a VIA SATA card with the 6421 chipset.
I have removed the VIA driver from C:WINDOWSSystem32drivers folder.
To remove the VIA driver:
1. Disable VIA card in Device Manager.
2. Go to C:WINDOWSSystem32drivers and remove "viamraid.sys" or "vsmraid.sys".
3. Re-Enable VIA card in Device Manager.
4. Re-Boot PC.
First you will want to check a couple of things.
Make sure the VIA driver is not installed by checking in Device Manager. Notice the yellow exclamation mark.
You also need to have PortIO and .Net 2.0 or higher installed. PortIO is included with Jungle Flasher and .Net can be obtained from Microsoft.
Go ahead and power on your Lite-ON drive with your connectivity kit or the XBOX 360.
Start up Jungle Flasher and go to the DVDkey 32 tab. You might have to change the I/O Port to find your Lite-ON.
Once you find it, you should see the properties listed under Drive properties.
Once you have identified your Lite-ON, you will want to do the following:
Eject tray
Power off the drive
Push the tray in half way
Power on the drive
Next you will click "Dummy from iXtreme"
Jungle Flasher will prompt you to save your dummy bin.
Save your dummy bin in a safe location where you won't delete it or lose it.
Make sure Jungle Flasher says it retrieved a good key
Jungle Flasher will ask you to autoload iXtreme firmware. Click YES.
This is the result of the autospoof.
Your DVDkey should be the same from the dummy bin to ix1.6.
Go back over to the MTKFlash tab and you are going to click Lite-ON erase.
It will prompt you once about having a correct DVDkey and then how to power cycle.
Pictured is the power cycle prompt, which is the 2nd and last prompt. Click Yes.
As soon as you click YES, you will power cycle the drive. That means shut it off for 1 second and turn it back on.
You should get good flash chip properties. (pictured is Winbond/NEX, some will have MXIC)
Go ahead and click WRITE.
Once it verifies OK, you can click Outro/ATA Reset and power off the drive.
Go ahead and test this out in your console.
Pats išbandžiau, viskas idealiai veikia pagal šitą guide.
Bionic Commando ant mano xBox360 nuflashinto pagal šį guide su iXtreme 1.6
As kiek pamenu senukuose kai reikejo paimiau visa T sesiakampiu komplekta, ir i 20lt tilpau. Arba tu ieskot nemoki, arba tingi..
Buvo vienas rinkinys, bet vos ne žaislinis vaikams, o paprastas T atsuktuvas 25Lt. :/ Kelias elektronikos pardas apėjau, o Senukuose nebuvau, nes man nepakeliui.
man dar reikėjo ko nors panašaus į ylą, o tai užkniso ten su savaržėle kruštis bandant pro tas vėdinimo skyles, kol atidarai..
Tokiais atvejais labai praverčia dantų krapštukai. Ir šiaip pirmą kartą išardyti X'ą yra sunkiausia. Paskui, tai 5-10min darbas, kartais nei tiek neužtrunku.
Tokiais atvejais labai praverčia dantų krapštukai. Ir šiaip pirmą kartą išardyti X'ą yra sunkiausia. Paskui, tai 5-10min darbas, kartais nei tiek neužtrunku.
Nu man tik 3 min užėmė plastmases nuimti, nes video prieš tai pažiūrėjau, kaip tai padaryti. Aišku, prieš tai tik 10min. reikėjo ieškoti tinkamo daikto, kuris lįstų pro vėdinimo skyles ir gale tas plokščias.. bet poto radau, tokį storą žiogelį ir peilį panaudojau gale. Nors kitam video rodė, kad priekį atidarai ir lenki į šoną, kol iššoksta gale viskas..